山梨酸废水在ABR中的基质降解行为

稳态条件下,采用厌氧折流板反应器(anaerobic baffled reactor,ABR)处理山梨酸废水并进行基质降解动力学研究.实验表明,在污泥负荷为0.54～1.63 kg COD/(kg VSS·d)的范围内,COD去除率随着负荷的增加从85%降到55%.各隔室出水COD沿程递减,前3个隔室承担了去除COD的重要作用,但随着污泥负荷的增加,后部承担的COD去除率比例增大.基于各串联隔室完全混合的假定,推导ABR中山梨酸废水的基质降解动力学方程,并通过实验确定相关动力学参数及相应的动力学方程.实测值与预测值基本吻合.     

Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.     

Improvement of the antifouling characteristics in a bioreactor of polypropylene microporous membrane by the adsorption of Tween 20

Surface modification by physical adsorption of Tween 20 was accomplished on polypropylene microporous membranes (PPMMs). Attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FT-IR) and scanning electron microscope (SEM) were used to characterize the chemical and morphological changes on the membrane surfaces. Water contact angles and relative pure water fluxes were measured. The data showed that the hydrophilic performance for the modified membranes increased with the increase in the adsorption amount of Tween 20 onto the surface or into the pores of polypropylene microporous membranes. To test the antifouling property of the membranes by the adsorption of Tween 20 in a membrane bioreactor (MBR), filtration for active sludge was performed using synthetic wastewater. With the help of the data of water fluxes and the FE-SEM photos of the modified PPMMs before or after operating in a MBR for about 12 d, the PPMMs with monolayer adsorption of Tween 20 showed higher remained flux and stronger antifouling ability than unmodified membrane and other modification membranes studied.     

生活垃圾生物处理的研究与展望

综述了国内外生活垃圾生物处理的研究进展和目前生活垃圾微生物研究水平，以及生活垃圾处理发展趋势与新动向，在此基础上提出了生活垃圾处理的建议和展望。     

厌氧-混凝工艺处理造纸厂终端废水试验研究

本文报告了用厌氧 -混凝工艺处理造纸厂终端废水的实验情况 ,在最佳实验条件下 ,废水从CODcr80 6 . 7m g/ L、BOD52 10 . 5 m g/ L、SS2 15 . 7m g/ L、OD4 650 . 35 0降至 CODcr6 1. 5 m g/ L、BOD52 7. 4m g/ L、SS17.3mg/ L、OD4 650 .0 11。实验结果表明对造纸厂终端废水的治理 ,本工艺是很有实用价值的一种方法     

Membrane fouling control by ultrasound in an anaerobic membrane bioreactor

In this study, ultrasound was used to control the membrane fouling online in an anaerobic membrane bioreactor (AMBR). Short-term running experiments were carried out under different operating conditions to explore feasible ultrasonic parameters. The experimental results indicated that when the crossflow velocity was more than 1.0 m/s, membrane fouling could be controlled effectively only by hydrodynamic methods without ultrasound. When ultrasound was applied, an ultrasonic power range of 60–150 W was suitable for the membrane fouling control in the experimental system. The experimental results showed that the membrane fouling was controlled so well that membrane filtration resistance (ΣR) could stay at 5 × 10¹¹ m⁻¹ for more than a week with the crossflow velocity of 0.75 m/s, which equaled the effect of crossflow velocity of more than 1.0 m/s without ultrasound. Translated from Techniques and Equipment for Environmental Pollution Control, 2006, 7(4): 25–29 [译自: 环境污染治理技术与设备]     

渗滤液回灌对填埋垃圾含水率的影响研究

文章通过模拟实验研究了不同的渗滤液回灌频率、回灌量和回灌速率对压实密度不同的垃圾的含水率的影响。研究表明,由于通道流的存在和影响,渗滤液的产生时间提前于填埋垃圾达到其有效贮水率的时间;渗滤液回灌频率越高、回灌量越大、回灌速率越慢、垃圾体温度越低、垃圾压实密度越高,则填埋垃圾的有效贮水率越大、含水率越高。在实施渗滤液回灌操作时,须综合考虑滤液回灌频率、回灌量、回灌速率、垃圾温度和垃圾压实密度等影响因素。     

A2/O工艺处理氨纶废水的应用研究

介绍了采用厌氧-缺氧-接触氧化(即A2/O)组合工艺处理氨纶生产废水的流程和设计参数,通过近半年的调试数据,反应季节对A2/O组合工艺处理氨纶生产废水的影响和可行性。提出运行过程中需要控制的参数,提供设计和运行参考。     

膜生物反应器膜污染的水力学控制实验研究

叙述了膜污染是影响膜-生物反应器处理技术推广应用的关键因素，采用水动力学方法是控制膜污染的有效方法。在不同污泥浓度条件下。对不同曝气强度下膜污染的发展速率及其形成机理进行了试验研究，研究结果表明：对应于不同污泥浓度均存在一个经济曝气强度，其大小随污泥浓度升高呈线性增加，膜生物反应器在经济曝气强度条件下运行可控制膜污染的发展；并从理论上推导出一个临界污泥浓度，其值为5．15g／L。对应于临界污泥浓度，并且污泥絮体在膜面可形成比较稳定的动态膜，膜过滤压差上升的速率最慢，膜生物反应器在此临界污泥浓度条件下运行膜污染发展最为缓慢。     

ABR反应器的设计

类似于多个UASB反应器串联起来运行的ABR反应器具有多种其它反应器不具备的优点，在处理化工颜料黄高盐生产废水的工程中，结合将高效复合微生物技术用于厌氧水解一连续曝气生化工艺取得成功；对ABR反应器而言，正确的设计参数是工程运行成功的保证。